Firmware with fuel injection functionality

All questions related to firmware
Post Reply
User avatar
STC
Posts: 13843
Joined: 30 Apr 2013, 23:41
Your CAR: AZLK 2140
SECU version: DIY SECU-3
Location: North Korea
Has thanked: 2160 times
Been thanked: 4335 times
Contact:

Firmware with fuel injection functionality

Post by STC »

A brief summary of injection

- 4 + 1 sets of injection tables
- Editing of parameters and fuel injection tables in real time (online);
- Simultaneous or single-point injection (in the near future will be implemented semi sequential injection and full sequential injection);
- The calculation method for fuel: Speed Density (uses MAP and AIR TEMP sensor);
- Open-loop IDLE algorithm. Supports PWM and STEPPER idle valve types. (in the near future will be implemented closed-loop idle control with PI regulator);
-O2 sensor AFR fuel correction, closed loop, narrow band (configurable);
- Acceleration enrichment (TPS based);
- Prime pulse (configurable);
- Over-run (configurable);
- RPM fuel cut-off.

Fuel injection tables:

- VE 16*16 (Volumetric efficiency);
- AFR 16-16 (Air/fuel ratio vs RMP and LOAD);
- Cranking PW (Injection pulse width on cranking);
- Warmup enrichment vs coolant temp;
- Injector’s dead time;
- IAC position vs coolant temp;
- IAC position on cranking;
- Afterstart enrichment vs coolant temp;
- Acceleration enrichment vs throttle movement speed;
- Acceleration enrichment vs RPM.
Author of the SECU-3™ project http://SECU-3.org. An open source engine control unit / Ignition control system, (C) 2007.
Клуб проекта в Facebook https://www.facebook.com/groups/secu3club
Клуб проекта ВКонтакте https://vk.com/secu3club (вступаем!)
tahiti-range
Posts: 2
Joined: 21 Nov 2015, 22:37
Your CAR: I go on foot
SECU version: official SECU-3T

Re: Firmware with fuel injection functionality

Post by tahiti-range »

Hi !

I have a Secu 3T, and I would like to use it to control the injection of my car. I have remapped the I/O to do it, but I cannot access the Fuel injection, Lambda control, and Acceleration parameters in the manager. The firmware and manager are the one from Feb 10 2015.

How can I access these options ?

Thanks in advance
User avatar
darxfame
Posts: 901
Joined: 10 Jul 2015, 19:12
Your CAR: ИЖ 2126 УМПО 1,7
SECU version: official SECU-3T
Location: Москва
Has thanked: 122 times
Been thanked: 137 times
Contact:

Re: Firmware with fuel injection functionality

Post by darxfame »

tahiti-range wrote:Hi !

I have a Secu 3T, and I would like to use it to control the injection of my car. I have remapped the I/O to do it, but I cannot access the Fuel injection, Lambda control, and Acceleration parameters in the manager. The firmware and manager are the one from Feb 10 2015.

How can I access these options ?

Thanks in advance
You must use fuel injection firmware to have access to this options. This link is a full binaries 7z archive file with all of versions firmware. There you can find the fuel injection version of firmware. https://github.com/ashabelnikov/secu3ap ... inaries.7z
ИЖ 2126 Ода, УМПО 3317,Январь 5.1 (Был Secu-3T M644), Фазированный впрыск(ДАД+ДТВ) (был Моновпрыск C16NZ)
User avatar
STC
Posts: 13843
Joined: 30 Apr 2013, 23:41
Your CAR: AZLK 2140
SECU version: DIY SECU-3
Location: North Korea
Has thanked: 2160 times
Been thanked: 4335 times
Contact:

Re: Firmware with fuel injection functionality

Post by STC »

Yes, darxfame is right!

Use firmware file, which name contains "inj".
Author of the SECU-3™ project http://SECU-3.org. An open source engine control unit / Ignition control system, (C) 2007.
Клуб проекта в Facebook https://www.facebook.com/groups/secu3club
Клуб проекта ВКонтакте https://vk.com/secu3club (вступаем!)
tahiti-range
Posts: 2
Joined: 21 Nov 2015, 22:37
Your CAR: I go on foot
SECU version: official SECU-3T

Re: Firmware with fuel injection functionality

Post by tahiti-range »

Thank you guys ! :D
Post Reply

Return to “Firmware”